Originally published December 2021. Updated August 2026 with additional detail and current Carbontex information.
A smooth, consistent drag matters most when a fish stays connected for a long time. Short runs are one thing. A prolonged fight with a powerful fish is where heat, changing drag pressure and tired tackle can become much more obvious.
Over the years we have received some memorable feedback from anglers using Carbontex drag washers in everything from small spinning reels to lever drags. Sharks, kingfish and yellowfin tuna have all featured in those reports. The stories below are useful because they show what anglers actually notice after upgrading and servicing a reel, rather than simply repeating a list of product claims.
Your drag has a simple job: allow line to leave the reel under controlled pressure. In practice, it has to keep doing that as the fish runs, stops, changes direction and runs again.
A drag that grabs or changes noticeably through a fight can put extra shock into your line, knots and hooks. A smooth drag is easier to trust because line can leave the reel progressively when the fish applies enough pressure. That matters with light tackle, but it also matters on heavier gear when a fight lasts long enough for the reel to be worked hard.
The drag washers are only part of the system. The condition of the metal washers, correct stack order, suitable drag grease where appropriate, bearings, line, knots and general reel condition all matter too. We look at a Carbontex upgrade as part of a proper reel service, not a magic cure for every reel problem.
One of the best examples came from Tony, who had upgraded the drag washers in a relatively inexpensive spinning reel. He later reported a roughly three-hour fight with a large shark, followed by several other fights lasting around 40 to 50 minutes with kingfish on another upgraded reel.
What interested us was not simply the size of the fish. It was what Tony noticed about the reel after sustained use. His feedback was that the drag pressure stayed consistent during the longer fights.
"I love how consistent the drag pressures are. There's no discernible fade on the longer fights."
Tony, Downrigger Shop customer
That is exactly the sort of real-world observation we value. The important part is not a laboratory number. It is an angler noticing predictable drag behaviour when the reel has been under load for a long time.
Another long-term customer, Richard, told us he had bought Carbontex sheet from us many years earlier, around 2011 by his recollection, and had used it across a range of reels. That included baitcasters and smaller lever-drag reels up to roughly Saltist 2-Speed 30 size.
He reported using those lever drags on fast-running fish including yellowfin tuna to about 30 kg, with the upgraded drags continuing to perform well. Again, that is customer experience rather than a controlled test, but it is useful long-term feedback from someone who had fitted the material to multiple reels and then fished them hard.
Taken together, these reports are why we keep coming back to the same point: if you already own a reel you like, servicing the drag and replacing tired friction washers can be a very worthwhile job before you replace the reel itself.
Pre-cut drag washers are convenient when the correct set is available for your exact reel. Sheet stock gives you a different advantage. You can use an original friction washer as the template and make replacements for several different reels, including older or less common models where a ready-made kit may be difficult to find.
Our current Carbontex sheet is 100 x 195 mm and is available in 0.5 mm and 1.0 mm thicknesses. Do not choose thickness solely because a reel is a spinner, baitcaster or overhead. Drag stacks vary between models and generations. Match the thickness of the friction washer you are replacing and preserve the correct overall stack height.
View Carbontex Drag Washer Sheet
The basic idea is straightforward. Remove the original friction washer, place it over the Carbontex sheet and reproduce its inside and outside diameters. Keeping the original washer gives you the most useful reference for both size and thickness.
Before taking anything apart, work somewhere clean and lay the drag components out in the exact order they came from the reel. A typical stack alternates friction washers with metal washers, but the arrangement is reel-specific and needs to go back together correctly.
Carbontex drag washers can be used dry or with a very light coating of suitable fishing reel drag grease. If you grease them, use a grease intended for reel drag systems and apply it sparingly. The old recommendation on this article mentioned automotive brake grease; we no longer recommend that. Reel-specific drag grease is the better choice.
Check the metal washers for damage or rough surfaces, reassemble the drag in its original order and make sure the retaining components seat correctly without being forced. Then test the drag before you go fishing. You want controlled, progressive line release throughout the useful adjustment range, not a drag that suddenly grabs or jumps.
For the complete cutting and fitting process, including disassembly, measuring, drilling, cutting and reassembly, use our dedicated step-by-step guide:
Read the Carbontex Drag Washer Installation Guide
The lesson from these older fishing reports still holds. A drag upgrade is not about chasing a bigger number on a spec sheet. It is about making a reel you already own behave predictably when a fish is pulling line and the pressure stays on.
If your reel's friction washers are worn, compressed or inconsistent, a service is the right time to inspect the whole drag stack. For anglers happy to cut their own replacements, Carbontex sheet lets you match the original washers and keep enough material on hand for other reels.
Already know the thickness you need? Our Carbontex drag washer sheet is available in 0.5 mm and 1.0 mm. If you are unsure, remove and measure an original friction washer first, or contact us with the exact reel model.